Posts Tagged ‘dress form’

My main goal with this dress right now is to combine the top and bottom pieces into one solid pattern. I pinned the top front and bottom front pieces together then removed all of the baste stitching. After ironing out the pinned pattern pieces, I pinned them to muslin. I cut out two panels from the muslin for the front and back panels. The solid pattern looks very obvious and I’m assuming that there is an easier way to do this eliminating a few steps for future reference.

After cutting out the pieces, I strategically pinned them together on the dress form. It worked! The two solid panels work just as well as when it was four pieces (top, bottom, front and back). I started to baste stitch the top and shoulder seams and will finish the rest tomorrow for a final fitting. Then it’s on to fabric shopping!

After removing the draped top pattern from the dress form, I ironed the material and cut around the edges to smooth out the lines. I then cut the pattern from another piece of muslin to create the top back panel.

Now that I have my two top pieces, I strategically draped them on the dress form. They both require bunching on the side and I wanted to make sure that the lines matched up from front to back. After I was happy with the way the bunching looked, I baste stitched the top panels together at the side, top and shoulder seams.

I placed the skirt panels back on the form and baste stitched them to the top panels with all seams matching up. I left open the seam that will hold the zipper so I could easily slide it off and on for fittings. After trying the dress on, I feel that it is ready for the final pattern. The only changes that will be made to the pattern are fusing the top and bottom panels into one. I also decided that I love the way the armpit hole on the left side is open which steps away from the original design. It adds just a touch of sexy to an overall classic gown.

I finally get to place the decorative waistband, which is something I have been looking forward to very much. There isn’t a how-to guide for something like this; it just takes some strategic placing and a lot of creativity. To do this, I placed the skirt onto the dress form inside out so the band could be properly pinned to the garment.

After making a few adjustments to the waistband and then trying the garment on, I stay-stitched the band into place. I don’t believe that this was an absolutely necessary step but I didn’t want it to slip out of place (better safe than sorry!).

Normally, I would opt for a machine stitch but the fabric overlapped a few times in the ruffle, which made it extremely thick. My fear was that I would break the machine needle. So, I decided on a simple hand stitch. I am very pleased with how it turned out:

Once the band was stitched into place and the pins were removed, I started to work on finishing the inside of the band. The fabric (as you can see) frays terribly. So, I wanted to use a finishing stitch on the machine to prevent further fraying. Big mistake! My initial fear about using a machine stitch was correct. I broke the needle. Stupidity or a right of passage? I’ll go with a right of passage. I decided to give it a rest for the night after the needle deal breaker…

Tonight, episode 2 of the new season of Project Runway. Can’t wait!!

I made my monthly pilgrimage today to the Garment District in search of fabric for the skirt I am currently working on. Believe it or not, I found the exact fabric that I was looking for at Paron Fabric’s. Paron is one of my faves because they have a good selection and the people there are helpful. I purchased 1.5 yds (extra for mistakes) of ivory-colored linen with a little stretch.

I opted against interfacing for both waistbands since the fabric is thicker than what I originally had in mind. They should maintain stiffness on their own. After folding and ironing the fabric, I pinned the pattern and cut the pieces out. The skirt panels are pinned at the seams on the dress form and are ready for dart placement tomorrow.

On another note, I found this amazing rust-colored fabric at the store. A few months ago when I conceptualized the Venice line, I designed a rust-colored gown with a built in corset. Needless to say, I am in LOVE with this fabric. It has a wet-shine look to it in certain light and an interesting texture. I spent some time draping the dress form with the fabric for new inspiration and ideas. I’m working on a design based on this concept: